Chapters: * SH CT OP CM Key / Action  ––  notes
Available as EDIT window contextual menus ED
Available as MIX window contextual menus MX
Active in Commands Keyboard Focus CF
KEYBOARD FOCUS ASSIGN TO..
Commands OP CM 1
Region List OP CM 2
Group List OP CM 3
OPERATION
Open Recent SH CM O
In Session Setup, Capture incoming TC  (window selected) ,
Link/Unlink Timeline and Edit Selections SH /
Copy Timeline Sel to Edit Sel CF 0  (qwerty)
Copy Edit Sel to Timeline Sel CF O  (letter)
tab Back CF L
tab Forward CF
Consolidate SEL SH OP 3
Create Tone at 1 kHz SH CT OP 3
Toggle ‘Tab To Transient’ tool OP CM TAB
Temp disable Grid SH drag
ZOOM / SCROLL
Zoom in/out of Timeline                      add CMD for fine OP up / down or scroll
Zoom in/out of Waveforms                 add CMD for fine SH OP up / down or scroll
Inc/Dec Track Height (w/ selection)    add OPT for ALL CT up / down or scroll
Fit ALL tracks to Edit window CT OP CM down arrow
Fit SEL tracks to Edit window CT OP CM up arrow
View entire session OP A
Vertical zoom in/out AUDIO OP CM ] / [
Vertical zoom in/out MIDI SH CM ] / [
Fill window width with SEL OP F
Previous zoom OP clik any zoom button
EDIT (using hand tool)
Move Start to SEL, Move Sync to SEL, Move End to SEL   **add OPT for COPY ED CT CM clik region
Snap region START to edit selection START CT clik region
Snap region SYNC to edit selection START SH CT clik region with sync point
Snap region END to edit selection START CT CM clik region
snap START of Sel to TC CF Y
snap SYNC of Sel to TC CF U
snap END of Sel to TC CF I
snap START of Sel to PLAYHEAD CF H
snap SYNC of Sel to PLAYHEAD CF J
snap END of Sel to PLAYHEAD CF K
make ref TONE at selection SH CT OP 3
cut from cursor to START of region CF A
cut from cursor to END of region CF C
fade from region START to cursor CF D
crossfade at selection CF F
fade to region END from cursor CF G
AUTOMATION
– write new breakpoint =NEXT value SH OP clik in track with finger
– write new breakpoint =PREV value OP CM clik in track with finger
– THIN at selection OP CM T
– Disable/Enable ALL Automation playlists on sel track SH CM clik Track View selector
Prev/Next Automation Track View on ALL tracks in current SEL CT CM left/right arrow keys
Prev/Next Automation Track View on ALL tracks CT OP CM left/right arrow keys
Show Automation of plug-in control, track vol, or pan CT CM clik on control
Enable/Disable Auto for ALL Plug-in Params CT OP CM clik on AUTO button
cut / paste PLUG-IN auto params CT OP C / V
Paste Special:  To Current Automation Type CT CM V
Paste Special:  Automation between different controls CT CM V
Cut Special:  To all automation parameters CT CM X
Show Clip Gain Info (Protools 10) SH CT =
Show Clip Gain Line (Protools 10) SH CT –
Copy Clip Gain (Protools 10) SH CT C
Paste Clip Gain (Protools 10) CT V
TRIM…
Trim UP TO, BUT NOT OVER, adj region CT while trimming
Trim region to SEL CM T
Separate at Insertion CM E
HEAL separation inside SEL CM H
Trim REGION START to Insertion CF A
Trim REGION END to Insertion CF S
NUDGE…  (grid)
all Nudge CF commands: Region (linked) / Time SEL (unlinked)
Back CF ,   or   –
Forward CF .   or   +
Back by NEXT LARGER VALUE CF M
Forward by NEXT LARGER VALUE CF /
Inc/Dec NUDGE value OP CM +/-
Inc/Dec GRID value CT OP +/-
SEL ONLY, NOT UNDERLYING AUDIO SH +/-
CLIP AUDIO ONLY within region CT +/-
Selection START SH OP +/-
Selection END SH CM +/-
Trim region START (by nudge) OP +/-
Trim region END (by nudge) CM +/-
AUDITIONING
Insertion follows playback   (Disable/Enable) CF N
Play Edit SEL CF [
Play Timeline SEL CF ]
Set and enable pre/post roll OP clik before/after sel
Play thru SEL Start by pre-post roll times CF 6/7  (querty keyboard)
Play thru SEL End by pre-post roll times CF 8/9  (querty keyboard)
Play by pre-roll to SEL Start/End OP left/right arrow keys
or     CURRENT LOC if no SEL CM left/right arrow keys
LOCATE
Recall Memory Location .  (1-99)  .
Edit Current Loc and Big Counter *
Edit Start/End counters /
Time entry in Transport OP CM /  (numeric keyboard)
Capture incoming TC in Spot and Time Stamp Selected dialogs =
**REGION COMMANDS:
constrain region to START at cursor or SEL START CT drag to track
constrain region to END at cursor or SEL START CT CM drag to track
Group regions OP CM G
Loop region OP CM L
WINDOW CONFIG
New or replace Window Config .  (1-99)  +
Recall Window Config .  (1-99)  *